| La vitrine de diffusion des publications et contributions des chercheurs de l'ÉTS |
| ENGLISH |
Liste des publications de "Bocher, Philippe"Nombre de documents archivés : 243. 2024
D'Andrea, A., Gagnon, M., Beretta, S. et Bocher, P..
2024.
« Measurements and prediction of extreme defect distributions for fatigue assessment in multi-pass weld of 13%Cr–4%Ni alloy for hydraulic turbines ».
International Journal of Fatigue, vol. 188.
Mirabi, Hamed, Mirakhorli, Fatemeh, Béland, Jean-François, Nadeau, François, Demers, Vincent et Bocher, Philippe.
2024.
« On selecting proper process parameters for cold metal transfer (CMT)–based wire arc additive manufacturing (WAAM) process ».
International Journal of Advanced Manufacturing Technology, vol. 133, nº 11-12.
pp. 6083-6093.
Pourdavood, Mohammad et Bocher, Philippe.
2024.
« Statistical modeling of microstructurally short crack growth in high cycle fatigue ».
Materials Science and Engineering: A, vol. 892.
2023
Barayjani, Hossein Taheri, Toroghinejad, Mohammad Reza, Rezaeian, Ahmad, Shabani, Ali et Bocher, Philippe.
2023.
« An investigation on microstructure and mechanical properties of a copper strip subjected to different routes of accumulative roll bonding process ».
Journal of Materials Engineering and Performance, vol. 32, nº 2.
pp. 651-659.
Pot, Clément, Yazdani, Majid, Boyadjian, Quentin, Bocher, Philippe et Béland, Jean-François.
2023.
« Texture and mechanical properties of extruded AA6063 aluminum alloy † ».
[Article de conférence]. Engineering Proceedings, vol. 43, nº 1.
Villié, Loïc, Cabrol, Elodie, Hof, Lucas, Feulvarch, Eric et Bocher, Philippe.
2023.
« Heterogeneities induced by uniaxial compression and resulting errors in material behavior assessment ».
International Journal of Material Forming, vol. 16, nº 6.
Yazdani, Majid, Pot, Clément, Boyadjian, Quentin, Liu, Yang, Yue, Stephen, Béland, Jean-François et Bocher, Philippe.
2023.
« Effect of unidirectional and cross-rolling on the texture evolution of a hot extruded AA6082 † ».
[Article de conférence]. Engineering Proceedings, vol. 43, nº 1.
2022
Giard, Gregory, Tousignant, Maxime, McMeekin, Kevin, Bellotto, Federico, Bocher, Philippe et Sirois, Frederic.
2022.
« Power-equivalent complex permeability model for nonlinear and hysteretic materials in the frequency domain for induction heating applications ».
IEEE Transactions on Magnetics, vol. 58, nº 6.
Kalush, Ali, Texier, Damien, Ecochard, Maxime, Sirvin, Quentin, Choquet, Karim, Gheno, Thomas, Vanderesse, Nicolas, Jomaa, Walid et Bocher, Philippe.
2022.
« Size effects on high temperature oxidation of MCrAlY coatings processed via APS and HVOF depositions ».
Surface and Coatings Technology, vol. 440.
Masoumi Khalilabad, Mahdi, Zedan, Yasser, Texier, Damien, Jahazi, Mohammad et Bocher, Philippe.
2022.
« Effect of heat treatments on microstructural and mechanical characteristics of dissimilar friction stir welded 2198/2024 aluminum alloys ».
Journal of Adhesion Science and Technology, vol. 36, nº 3.
pp. 221-239.
Slamani, Fateh, Thibault, Denis, Verreman, Yves et Bocher, Philippe.
2022.
« A new morphology of retained austenite obtained by intercritical tempering of 13Cr-4Ni martensitic stainless steel ».
Materials Characterization, vol. 193.
Vanderesse, Nicolas, Bocher, Philippe, Nuño, Natalia, Yánez, Alejandro et Hof, Lucas A..
2022.
« On the characterization of roughness and geometrical irregularities of additively manufactured single titanium-alloy struts ».
Additive Manufacturing, vol. 54.
2021Bridier, Florent, Bocher, Philippe, Cormier, Jonathan et Villechaise, Patrick (inventeurs) 5 octobre 2021. « Method for heat treating by induction an alloy component for generating microstructure gradients and an alloy component heat treated according to the method ». École de technologie supérieure, Institut supérieur de l'aéronqutique et de l'espace - École nationale supérieure de mécanique et d'aérotechnique (ISAEENSMA) (titulaire(s)). US 11,136,634.
Foroozmehr, Fayaz et Bocher, Philippe.
2021.
« An investigation on fracture toughness of the heat-affected zone in the welded joints of 13% Cr-4% Ni martensitic stainless steels ».
Fatigue and Fracture of Engineering Materials and Structures, vol. 44, nº 12.
pp. 3416-3430.
Herrera-Jimenez, E. J., Vanderesse, N., Bousser, E., Schmitt, T., Bocher, P., Martinu, L. et Klemberg-Sapieha, J. E..
2021.
« Fracture mechanism of TiN coatings on Ti-6Al-4V substrates : Role of interfaces and of the residual stress depth profile ».
Surface and Coatings Technology, vol. 426.
Maurel, Pierre, Weiss, Laurent, Bocher, Philippe et Grosdidier, Thierry.
2021.
« Effects of SMAT at cryogenic and room temperatures on the kink band and martensite formations with associated fatigue resistance in a β-metastable titanium alloy ».
Materials Science and Engineering: A, vol. 803.
Milton, Samuel, Rigo, Olivier, LeCorre, Sebastien, Morandeau, Antoine, Siriki, Raveendra, Bocher, Philippe et Leroy, Rene.
2021.
« Microstructure effects on the machinability behaviour of Ti6Al4V produced by Selective Laser Melting and Electron Beam Melting process ».
Materials Science and Engineering: A, vol. 823.
Perard, Thomas, Sova, Alexey, Robe, Hugo, Robin, Vincent, Zedan, Yasser, Bocher, Philippe et Feulvarch, Eric.
2021.
« Friction stir processing of austenitic stainless steel cold spray coating deposited on 304L stainless steel substrate: Feasibility study ».
International Journal of Advanced Manufacturing Technology, vol. 115, nº 7-8.
pp. 2379-2393.
Zedan, Y., Iben Houria, M., Vanderesse, N., Atmani, F., Mirakhorli, F., Nadeau, F., Demers, V. et Bocher, P..
2021.
« Fatigue properties of continuous wave and pulsed wave laser cold-wire welding of thick section AA6005-T6 aluminum alloys ».
International Journal of Fatigue, vol. 147.
2020
Ajaja, J., Jomaa, W., Bocher, P., Chromik, R. R. et Brochu, M..
2020.
« High cycle fatigue behavior of hard turned 300 M ultra-high strength steel ».
International Journal of Fatigue, vol. 131.
Bag, Amrita, Delbergue, Dorian, Ajaja, Jihane, Bocher, Philippe, Lévesque, Martin et Brochu, Myriam.
2020.
« Effect of different shot peening conditions on the fatigue life of 300M steel submitted to high stress amplitudes ».
International Journal of Fatigue, vol. 130.
Boyadjian, Quentin, Vanderesse, Nicolas, Toews, Matthew et Bocher, Philippe.
2020.
« Detecting defects in materials using deep convolutional neural networks ».
In Image Analysis and Recognition : 17th International Conference, ICIAR 2020, Póvoa de Varzim, Portugal, June 24–26, 2020, Proceedings, Part I (Póvoa de Varzim, Portugal, June 24-26, 2020)
Coll. « Lecture Notes in Computer Science », vol. 12131.
pp. 293-306.
Springer.
Bretin, R., Levesque, M., Pilvin, P. et Bocher, P..
2020.
« Neighborhood effect within polycrystalline materials: Elastoplastic micromechanical analysis by cellular automaton and finite element ».
International Journal of Fatigue, vol. 137.
Chadha, Kanwal, Tian, Yuan, Bocher, Philippe, Spray, John G. et Aranas, Clodualdo.
2020.
« Microstructure evolution, mechanical properties and deformation behavior of an additively manufactured maraging steel ».
Materials, vol. 13, nº 10.
Dureau, Clément, Novelli, Marc, Arzaghi, Mandana, Massion, Roxane, Bocher, Philippe, Nadot, Yves et Grosdidier, Thierry.
2020.
« On the influence of ultrasonic surface mechanical attrition treatment (SMAT) on the fatigue behavior of the 304L austenitic stainless steel ».
Metals, vol. 10, nº 1.
Foroozmehr, Fayaz et Bocher, Philippe.
2020.
« Effect of low temperature intercritical heat-treatment on stable crack growth behavior in 13% Cr-4% Ni martensitic stainless steel multipass weldments ».
Engineering Fracture Mechanics, vol. 240.
Foroozmehr, Fayaz et Bocher, Philippe.
2020.
« On the ductile rupture of 13% Cr-4% Ni martensitic stainless steels ».
International Journal of Fracture, vol. 224, nº 1.
pp. 67-82.
Godin, Stéphane, Hamel-Akré, Johann, Thibault, Denis, Serventi, Alessandra-Maria et Bocher, Philippe.
2020.
« Ni and Mn enrichment effects on reformed austenite: thermodynamical and low cycle fatigue stability of 13%Cr–4%Ni and 13%Cr–6%Ni stainless steels ».
SN Applied Sciences, vol. 2, nº 3.
Jamshidinia, Mahdi, Ghasemi-Nanesa, Hadi, Bocher, Philippe, Nuno, Natalia, Poorganji, Behrang et Habibnejad-Korayem, Mahdi.
2020.
« Microstructural alteration of alloyed steel in direct metal laser melting by powder bed deposition system ».
Steel Research International, vol. 91, nº 10.
Maurel, Pierre, Weiss, Laurent, Bocher, Philippe, Fleury, Eric et Grosdidier, Thierry.
2020.
« Mechanisms of oxide dependent tribological behavior in Ti / Steel sliding and influence of nanostructured surfaces ».
In 14th World Conference on Titanium (Ti 2019) (Nantes, France, June 10-14, 2020)
Coll. « MATEC Web Conferences », vol. 321.
EDP Sciences.
Maurel, Pierre, Weiss, Laurent, Grosdidier, Thierry et Bocher, Philippe.
2020.
« How does surface integrity of nanostructured surfaces induced by severe plastic deformation influence fatigue behaviors of Al alloys with enhanced precipitation? ».
International Journal of Fatigue, vol. 140.
Saadati, Yousef, Chatelain, Jean-François, Lebrun, Gilbert, Beauchamp, Yves, Bocher, Philippe et Vanderesse, Nicolas.
2020.
« A study of the interlaminar fracture toughness of unidirectional flax/epoxy composites ».
Journal of Composites Science, vol. 4, nº 2.
Tabiai, I., Texier, D., Bocher, P., Therriault, D. et Levesque, M..
2020.
« In-situ full field out of plane displacement and strain measurements at the micro-scale in single reinforcement composites under transverse load ».
Experimental Mechanics, vol. 60, nº 3.
pp. 359-377.
Toubal, Lofti, Chaabouni, Hamed, Bocher, Philippe et Jianqiang, Chen.
2020.
« Monitoring fracture of high-strength steel under tensile and constant loading using acoustic emission analysis ».
Engineering Failure Analysis, vol. 108.
Vanderesse, N., Texier, D. et Bocher, P..
2020.
« Effect of porosities on brazed martensitic steel tensile properties: 2D and 3D pre-mortem vs post-mortem characterizations ».
Materials Characterization, vol. 160.
2019
Ajaja, J., Jomaa, W., Bocher, P., Chromik, R. R., Songmene, V. et Brochu, M..
2019.
« Hard turning multi-performance optimization for improving the surface integrity of 300M ultra-high strength steel ».
International Journal of Advanced Manufacturing Technology, vol. 104, nº 1-4.
pp. 141-157.
Bag, Amrita, Delbergue, Dorian, Bocher, Philippe, Lévesque, Martin et Brochu, Myriam.
2019.
« Statistical analysis of high cycle fatigue life and inclusion size distribution in shot peened 300M steel ».
International Journal of Fatigue, vol. 118.
pp. 126-138.
Bertrand, Rémi, Robe, Hugo, Texier, Damien, Zedan, Yasser, Feulvarch, Eric et Bocher, Philippe.
2019.
« Analysis of AA2XXX/AA7XXX friction stir welds ».
Journal of Materials Processing Technology, vol. 271.
pp. 312-324.
Bianchetti, C., Delbergue, D., Bocher, Philippe, Levesque, M. et Brochu, M..
2019.
« Analytical fatigue life prediction of shot peened AA 7050-T7451 ».
International Journal of Fatigue, vol. 118.
pp. 271-281.
Bretin, R., Levesque, M. et Bocher, P..
2019.
« Neighborhood effect on the strain distribution in linearly elastic polycrystals: Part 1 Finite element study of the interaction between grains ».
International Journal of Solids and Structures, vol. 176-177.
pp. 36-48.
Bretin, R., Levesque, M. et Bocher, P..
2019.
« Neighborhood effect on the strain distribution in linearly elastic polycrystals: Part 2 - Cellular Automaton ».
International Journal of Solids and Structures, vol. 176-177.
pp. 49-67.
Delbergue, Dorian, Texier, Damien, Lévesque, Martin et Bocher, Philippe.
2019.
« Diffracting-grain identification from electron backscatter diffraction maps during residual stress measurements: a comparison between the sin2ψ and cosα methods ».
Journal of Applied Crystallography, vol. 52, nº 4.
pp. 828-843.
Ebrahimi, G. R., Momeni, A., Ezatpour, H. R., Jahazi, M. et Bocher, P..
2019.
« Dynamic recrystallization in Mone1400 Ni-Cu alloy: mechanism and role of twinning ».
Materials Science and Engineering: A, vol. 744.
pp. 376-385.
Javadi, Hamid, Jomaa, Walid, Songmene, Victor, Brochu, Myriam et Bocher, Philippe.
2019.
« Inconel 718 superalloy controlled surface integrity for fatigue applications produced by precision turning ».
International Journal of Precision Engineering and Manufacturing, vol. 20, nº 8.
pp. 1297-1310.
Khalifa, Mohamed, Barka, Noureddine, Brousseau, Jean et Bocher, Philippe.
2019.
« Optimization of the edge effect of 4340 steel specimen heated by induction process with flux concentrators using finite element axis-symmetric simulation and experimental validation ».
International Journal of Advanced Manufacturing Technology, vol. 104, nº 9-12.
pp. 4549-4557.
Khalifa, Mohamed, Barka, Noureddine, Brousseau, Jean et Bocher, Philippe.
2019.
« Reduction of edge effect using response surface methodology and artificial neural network modeling of a spur gear treated by induction with flux concentrators ».
International Journal of Advanced Manufacturing Technology, vol. 104, nº 1-4.
pp. 103-117.
Khalifa, Mohamed, Barka, Noureddine, Brousseau, Jean et Bocher, Philippe.
2019.
« Sensitivity study of hardness profile of 4340 steel disc hardened by induction according to machine parameters and geometrical factors ».
International Journal of Advanced Manufacturing Technology, vol. 101, nº 1-4.
pp. 209-221.
Liu, J. H., Vanderesse, N., Stinville, J. C., Pollock, T. M., Bocher, P. et Texier, D..
2019.
« In-plane and out-of-plane deformation at the sub-grain scale in polycrystalline materials assessed by confocal microscopy ».
Acta Materialia, vol. 169.
pp. 260-274.
Maurel, Pierre, Weiss, Laurent, Bocher, Philippe, Fleury, Eric et Grosdidier, Thierry.
2019.
« Oxide dependent wear mechanisms of titanium against a steel counterface: influence of SMAT nanostructured surface ».
Wear, vol. 430-431.
pp. 245-255.
Sun, Binhan, Ma, Yan, Vanderesse, Nicolas, Varanasi, Rama Srinivas, Song, Wenwen, Bocher, Philippe, Ponge, Dirk et Raabe, Dierk.
2019.
« Macroscopic to nanoscopic in situ investigation on yielding mechanisms in ultrafine grained medium Mn steels: role of the austenite-ferrite interface ».
Acta Materialia, vol. 178.
pp. 10-25.
Touahir, Kamel, Bilek, Ali, Bocher, Philippe et Beldi, Mustapha.
2019.
« Experimental and numerical analysis of the fields of the frozen stresses in an epoxy sphere using the stress-freezing method and mechanical slicing ».
Journal of Materials and Engineering Structures, vol. 6, nº 2.
Touazine, Heithem, Chadha, Kanwal, Jahazi, Mohammad et Bocher, Philippe.
2019.
« Characterization of subsurface microstructural alterations induced by hard turning of Inconel 718 ».
Journal of Materials Engineering and Performance, vol. 28, nº 11.
pp. 7016-7024. 2018
Chen, Jianqiang, Demers, Vincent, Turner, Daniel P. et Bocher, Philippe.
2018.
« Experimental investigation on high-cycle fatigue of inconel 625 superalloy brazed joints ».
Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, vol. 49A, nº 4.
pp. 1244-1253.
Chuitcheu, James William, Texier, Damien et Bocher, Philippe.
13 mars 2018.
« Determining Properties of Materials at High Temperatures ».
[Article de recherche]. Substance ÉTS.
Chuitcheu, James William, Texier, Damien et Bocher, Philippe.
13 mars 2018.
« Déterminer les propriétés des matériaux à haute température ».
[Article de recherche]. Substance ÉTS.
Chuitcheu, James William, Texier, Damien et Bocher, Philippe.
4 avril 2018.
« Hot Tensile Strength Micromachine for Aeronautics ».
[Article de recherche]. Substance ÉTS.
Chuitcheu, James William, Texier, Damien et Bocher, Philippe.
4 avril 2018.
« Une micromachine de traction à chaud pour l’aéronautique ».
[Article de recherche]. Substance ÉTS.
Hoa Ngan, Nguyen et Bocher, Philippe.
2018.
« Finite element analysis simulation of the effect of induction hardening on rolling contact fatigue ».
Journal of Tribology, vol. 140, nº 6.
Javadi, Hamid, Jomaa, Walid, Dalgaard, Elvi, Brochu, Myriam et Bocher, Philippe.
2018.
« Influence of surface residual stresses on the fatigue life and crack propagation behavior of turned Inconel 718 super-alloy ».
In 12th International Fatigue Congress (FATIGUE 2018) (Poitiers, France, May 27-June 1, 2018)
Coll. « MATEC Web of Conferences », vol. 165.
EDP Sciences.
Klotz, T., Delbergue, D., Bocher, P., Levesque, M. et Brochu, M..
2018.
« Surface characteristics and fatigue behavior of shot peened Inconel 718 ».
International Journal of Fatigue, vol. 110.
pp. 10-21.
Liu, Heli, Liu, Huaiju, Bocher, Philippe, Zhu, Caichao et Sun, Zhangdong.
2018.
« Effects of case hardening properties on the contact fatigue of a wind turbine gear pair ».
International Journal of Mechanical Sciences, vol. 141.
pp. 520-527.
Masoumi Khalilabad, Mahdi, Zedan, Yasser, Texier, Damien, Jahazi, Mohammad et Bocher, Philippe.
2018.
« Effect of tool geometry and welding speed on mechanical properties of dissimilar AA2198–AA2024 FSWed joint ».
Journal of Manufacturing Processes, vol. 34, part A.
pp. 86-95.
Nazemi, Faranak, Hamel-Akré, Johann et Bocher, Philippe.
2018.
« Modeling of cementite coarsening during tempering of low-alloyed-medium carbon steel ».
Journal of Materials Science, vol. 53, nº 8.
pp. 6198-6218.
Novelli, M., Bocher, P. et Grosdidier, T..
2018.
« Effect of cryogenic temperatures and processing parameters on gradient-structure of a stainless steel treated by ultrasonic surface mechanical attrition treatment ».
Materials Characterization, vol. 139.
pp. 197-207.
Texier, D., Atmani, F., Bocher, P., Nadeau, F., Chen, J., Zedan, Y., Vanderesse, N. et Demers, V..
2018.
« Fatigue performances of FSW and GMAW aluminum alloys welded joints: Competition between microstructural and structural-contact-fretting crack initiation ».
International Journal of Fatigue, vol. 116.
pp. 220-233.
Tolouei, Ehsan, Toroghinejad, Mohammad Reza, Asgari, Hamed, Monajati Zadeh, Hossein, Ashrafizadeh, Fakhreddin, Szpunar, Jerzy A. et Bocher, Philippe.
2018.
« Microstructure and texture development in Al-3%Brass composite produced through ARB ».
Advanced Engineering Materials, vol. 20, nº 4.
Touahir, Kamel, Bilek, Ali, Larbi, Said, Djebali, Said et Bocher, Philippe.
2018.
« 3D stress analysis of a loaded birefringent sphere by photoelastic experiment and finite elements method ».
In 24th Conference on Applications of Computer Algebra (Santiago de Compostela, Spain, June 18-22, 2018)
Tu, Fubin, Delbergue, Dorian, Klotz, Thierry, Bag, Amrita, Miao, Hongyan, Bianchetti, Charles, Brochu, Myriam, Bocher, Philippe et Levesque, Martin.
2018.
« Discrete element-periodic cell coupling model and investigations on shot stream expansion, Almen intensities and target materials ».
International Journal of Mechanical Sciences, vol. 145.
pp. 353-366.
Vanderesse, N., Larregain, B., Bridier, F. et Bocher, P..
2018.
« Experimental assessment of high heating rates in induction heating with temperature-sensitive lacquers ».
Journal of Materials Engineering and Performance, vol. 27, nº 8.
pp. 3831-3843.
Vanderesse, N., Richter, A., Nuño, N. et Bocher, P..
2018.
« Measurement of deformation heterogeneities in additive manufactured lattice materials by Digital Image Correlation: Strain maps analysis and reliability assessment ».
Journal of the Mechanical Behavior of Biomedical Materials, vol. 86.
pp. 397-408.
Wang, Wei, Liu, Huaiju, Zhu, Caichao, Bocher, Philippe, Liu, Heli et Sun, Zhangdong.
2018.
« Evaluation of rolling contact fatigue of a carburized wind turbine gear considering the residual stress and hardness gradient ».
Journal of Tribology, vol. 140, nº 6.
2017
Anderson, M., Thielin, A. L., Bridier, F., Bocher, P. et Savoie, J..
2017.
« δ Phase precipitation in Inconel 718 and associated mechanical properties ».
Materials Science and Engineering: A, vol. 679.
pp. 48-55.
Bag, Amrita, Delbergue, Dorian, Lévesque, Martin, Bocher, Philippe et Brochu, Myriam.
2017.
« Study of short crack growth in shot peened 300M steel ».
In 13th International Conference on Shot Peening: ICSP13: Proceedings (Montréal, QC, Canada, 18-21 sept. 2017)
pp. 230-235.
Bertrand, R., Texier, D., Robe, H., Zedan, Y., Feulvarch, E. et Bocher, P.. 2017. « Heterogeneous mechanical behavior of dissimilar FSWed joints assessed by OHR-DIC characterizations ». Communication lors de la conférence : 5th International Conference on Scientific and Technical Advances on Friction Stir Welding & Processing (Metz, France, Oct. 11-13, 2017).
Castro Moreno, A., Tu, F., Lévesque, M. et Bocher, P..
2017.
« Shot peening FEM simulation: A novel approach based on crystal plasticity ».
In 13th International Conference on Shot Peening: ICSP13: Proceedings (Montréal, QC, Canada, 18-21 sept. 2017)
pp. 260-265.
Chen, Jianqiang, Demers, Vincent, Cadotte, Eve-Line, Turner, Daniel et Bocher, Philippe.
2017.
« Structural performance of inconel 625 superalloy brazed joints ».
Journal of Materials Engineering and Performance, vol. 26, nº 2.
pp. 547-553.
Comot, P., Bocher, P. et Belanger, P..
2017.
« Ultrasonic guided wave inspection of Inconel 625 brazed lap joints: Simulation and experimentation ».
NDT and E International, vol. 91.
pp. 71-78.
Delbergue, D., Lévesque, M. et Bocher, P..
2017.
« About the importance of X-ray elastic constant determination in the precise measurement of residual stress profiles ».
In 13th International Conference on Shot Peening: ICSP13: Proceedings (Montréal, QC, Canada, 18-21 sept. 2017)
pp. 236-242.
Delbergue, D., Texier, D., Lévesque, M. et Bocher, P..
2017.
« Comparison of two X-Ray residual stress measurement methods: Sin2 ψ and Cos α, through the determination of a martensitic steel X-Ray elastic constant ».
In International Conference on Residual Stresses 2016 ICRS-10
Coll. « Materials Research Proceedings »
pp. 55-60.
Millersville : Materials Research Forum LLC.
Demers, V., Elmajdoubi, M. M. et Bocher, P..
2017.
« Moldability of low-pressure powder injection molding feedstocks ».
In Advances in Powder Metallurgy & Particulate Materials 2017 : Conference Proceedings (Las Vegas , NV, USA, June 13-16, 2017)
pp. 401-414.
Metal Powder Industries Federation.
Foroozmehr, Fayaz, Verreman, Yves, Chen, Jianqiang, Thibault, Denis et Bocher, Philippe.
2017.
« Effect of inclusions on fracture behavior of cast and wrought 13% Cr-4% Ni martensitic stainless steels ».
Engineering Fracture Mechanics, vol. 175.
pp. 262-278. Hernández, Pedro Gálvez, Lafarga, Xavier Aguilo, Vanderesse, Nicolas, Quevedo González, Fernando, Bocher, Philippe et Nuño, Natalia. 2017. « Analysis of porous TI-6AL-4V structures made by selective laser sintering for intervertebral cages ». Communication lors de la conférence : 23rd Congress of the European Society of Biomechanics (Sevilla, Spain, July 02-05, 2017).
Javadi, Hamid, Jomaa, Walid, Texier, Damien, Brochu, Myriam et Bocher, Philippe.
2017.
« Surface roughness effects on the fatigue behavior of as-machined inconel 718 ».
In 8th International Conference on Materials Structure and Micromechanics of Fracture (MSMF 8) (Brno, Czech republic, July 27-29, 2016)
Coll. « Solid State Phenomena », vol. 258.
pp. 306-309.
Trans Tech Publications Ltd.
Jomaa, Walid, Gakwaya, Augustin et Bocher, Philippe.
2017.
« Modeling of materials behavior in finite element analysis and simulation of machining processes : Identification techniques and challenges ».
In
Advanced Machining Processes: Innovative Modeling Techniques.
Coll. « Manufacturing Design and Technology Series ».
pp. 281-318. Boca Raton : CRC Press.
Jomaa, Walid, Lévesque, Julie, Bocher, Philippe, Divialle, Arnaud et Gakwaya, Augustin.
2017.
« Optimization study of dry peripheral milling process for improving aeronautical part integrity using Grey relational analysis ».
International Journal of Advanced Manufacturing Technology, vol. 91, nº 1-4.
pp. 931-942.
Jomaa, Walid, Mechri, Oussama, Levesque, Julie, Songmene, Victor, Bocher, Philippe et Gakwaya, Augustin.
2017.
« Finite element simulation and analysis of serrated chip formation during highspeed machining of AA7075T651 alloy ».
Journal of Manufacturing Processes, vol. 26.
pp. 446-458.
Jomaa, Walid, Songmene, Victor et Bocher, Philippe.
2017.
« Predictive analytical modeling of cutting forces generated by high-speed machining of ductile and hard metals ».
Machining Science and Technology, vol. 21, nº 3.
pp. 335-361.
Jomaa, Walid, Songmene, Victor, Bocher, Philippe et Gakwaya, Augustin.
2017.
« Fea-based comparative investigation on high speed machining of aluminum alloys aa6061-t6 and aa7075-t651 ».
In 9th International Congress on Precision Machining, (ICPM 2017) (Athens, Greece, Sept. 06-09, 2017)
Coll. « Solid State Phenomena », vol. 261.
pp. 347-353.
Klotz, Thierry, Delbergue, Dorian, Miao, Hong-Yan, Bocher, Philippe, Lévesque, Martin et Brochu, Myriam.
2017.
« Analytical fatigue life prediction of shot peened Inconel 718 ».
In 13th International Conference on Shot Peening: ICSP13: Proceedings (Montréal, QC, Canada, 18-21 sept. 2017)
pp. 243-252.
Lafarga, Xavier Aguilo, Hernández, Pedro Gálvez, Vanderesse, Nicolas, González, Fernando Quevedo, Bocher, Philippe et Nuño, Natalia. 2017. « Effect of the building orientation on mechanical properties of porous structures made by additive manufacturing ». Communication lors de la conférence : 23rd Congress of the European Society of Biomechanics (Sevilla, Spain, July 02-05, 2017).
McMeekin, Kevin, Sirois, Frédéric, Tousignant, Maxime et Bocher, Philippe.
2017.
« Improving the accuracy of time-harmonic FE simulations in induction heating applications Towards better ferromagnetic material models ».
COMPEL - The International Journal for Computation and Mathematics in Electrical and Electronic Engineering, vol. 36, nº 2.
pp. 526-534.
Meimandi, Shilan, Vanderesse, Nicolas, Thibault, Denis, Bocher, Philippe et Viens, Martin.
2017.
« Macro-defects characterization in cast CA-6NM martensitic stainless steel ».
Materials Characterization, vol. 124.
pp. 31-39.
Novelli, M., Maurel, P., Weiss, L., Grosdidier, T. et Bocher, P..
2017.
« Stress-Assisted and Strain-Induced Martensites formed by cryogenic ultrasonic shot peening in austenitic stainless steels ».
In 13th International Conference on Shot Peening: ICSP13: Proceedings (Montréal, QC, Canada, 18-21 sept. 2017)
pp. 510-515.
Siredey-Schwaller, N., Hamel-Akre, J., Peltier, L., Hazotte, A. et Bocher, P..
2017.
« Solidification sequence of Ni-Si-Cr ~3wt% B brazing alloys ».
Welding in the World, vol. 61, nº 6.
pp. 1253-1265.
Stinville, J. C., Echlin, M. P., Callahan, P. G., Miller, V. M., Texier, D., Bridier, F., Bocher, P. et Pollock, T. M..
2017.
« Measurement of strain localization resulting from monotonic and cyclic loading at 650C in nickel base superalloys ».
Experimental Mechanics, vol. 57, nº 8.
pp. 1289-1309.
Sun, Binhan, Vanderesse, Nicolas, Fazeli, Fateh, Scott, Colin, Chen, Jianqiang, Bocher, Philippe, Jahazi, Mohammad et Yue, Stephen.
2017.
« Discontinuous strain-induced martensite transformation related to the Portevin-Le Chatelier effect in a medium manganese steel ».
Scripta Materialia, vol. 133.
pp. 9-13. Thibault, Denis, Meimandi, Shilan, Vanderesse, Nicolas, Bocher, Philippe, Viens, Martin, Brochu, Myriam et Gagnon, Martin. 2017. « Linking defects found by non-destructive testing in stainless steel castings to the fatigue analysis of hydraulic turbines ». Communication lors de la conférence : 3rd International Symposium on Fatigue Design and Material Defects (FDMD) (Lecco, Italy, Sept. 19-22, 2017).
Touazine, Heithem, Akab, Jordan, Jahazi, Mohammad, Tahan, Antoine, Jomaa, Walid et Bocher, Philippe.
2017.
« Modeling of the microstructure alteration induced by hard turning of Inconel 718 ».
International Journal of Advanced Manufacturing Technology, vol. 93, nº 9-12.
pp. 3705-3712.
Touazine, Heithem, Jahazi, Mohammad et Bocher, Philippe.
2017.
« Accurate determination of damaged subsurface layers in machined Inconel 718 ».
International Journal of Advanced Manufacturing Technology, vol. 88, nº 9-12.
pp. 3419-3427.
Tu, Fubin, Delbergue, Dorian, Miao, Hongyan, Klotz, Thierry, Brochu, Myriam, Bocher, Philippe et Levesque, Martin.
2017.
« A sequential DEM-FEM coupling method for shot peening simulation ».
Surface and Coatings Technology, vol. 319.
pp. 200-212. 2016
Aghasibeig, Maniya, Monajatizadeh, Hossein, Bocher, Philippe, Dolatabadi, Ali, Wuthrich, Rolf et Moreau, Christian.
2016.
« Cold spray as a novel method for development of nickel electrode coatings for hydrogen production ».
International Journal of Hydrogen Energy, vol. 41, nº 1.
pp. 227-238.
Amrei, Mohsen Mokhtabad, Monajati, Hossein, Thibault, Denis, Verreman, Yves et Bocher, Philippe.
2016.
« Effects of various post-weld heat treatments on austenite and carbide formation in a 13Cr4Ni steel multipass weld ».
Metallography, Microstructure, and Analysis, vol. 5, nº 1.
pp. 50-61.
Amrei, Mohsen Mokhtabad, Monajati, Hossein, Thibault, Denis, Verreman, Yves, Germain, Lionel et Bocher, Philippe.
2016.
« Microstructure characterization and hardness distribution of 13Cr4Ni multipass weld metal ».
Materials Characterization, vol. 111.
pp. 128-136.
Anderson, M., Bridier, F., Gholipour, J., Jahazi, M., Wanjara, P., Bocher, P. et Savoie, J..
2016.
« Mechanical and metallurgical evolution of stainless steel 321 in a multi-step forming process ».
Journal of Materials Engineering and Performance, vol. 25, nº 4.
pp. 1526-1538.
Comot, Pierre, Bocher, Philippe et Belanger, Pierre.
2016.
« Ultrasonic guided wave inspection of Inconel 625 brazed lap joints ».
In Nondestructive Characterization and Monitoring of Advanced Materials, Aerospace, and Civil Infrastructure 2016 (Las Vegas , NV, USA, Mar. 20-24, 2016)
Coll. « Proceedings of SPIE », vol. 9804.
SPIE.
Elhadi, A., Bouchoucha, A., Jomaa, W., Zedan, Y., Schmitt, T. et Bocher, P..
2016.
« Study of surface wear and damage induced by dry sliding of tempered AISI 4140 steel against hardened AISI 1055 steel ».
Tribology in Industry, vol. 38, nº 4.
pp. 475-485.
Giraud, Landry, Robe, Hugo, Claudin, Christophe, Desrayaud, Christophe, Bocher, Philippe et Feulvarch, Eric.
2016.
« Investigation into the dissimilar friction stir welding of AA7020-T651 and AA6060-T6 ».
Journal of Materials Processing Technology, vol. 235.
pp. 220-230.
Jomaa, W., Mechri, J., Lévesque, J., Gakwaya, A., Songmene, V. et Bocher, P..
2016.
« Finite element analysis of serrated chip formation in machining of 7075-T651 alluminum alloy ».
In XXVIII International Mineral Processing Congress (IMPC) (Québec, QC, Canada, Sept. 11-15, 2016)
Jomaa, W., Songmene, V. et Bocher, P..
2016.
« An investigation of machining-induced residual stresses and microstructure of induction-hardened AISI 4340 steel ».
Materials and Manufacturing Processes, vol. 31, nº 7.
pp. 838-844.
Jomaa, Walid, Songmene, Victor et Bocher, Philippe.
2016.
« An hybrid approach based on machining and dynamic tests data for the identification of material constitutive equations ».
Journal of Materials Engineering and Performance, vol. 25, nº 3.
pp. 1010-1027.
Masoumi, Mahdi, Zedan, Yasser, Texier, Damien, Jahazi, Mohammad et Bocher, Philippe.
2016.
« Friction stir welding of AA2024 and AA2198 Aluminum alloys: effect of tool geometry and process parameters ».
In 2nd International Conference on Welding and Non Destructive Testing (ICWNDT) (Tehran, Iran, Dec. 20-21, 2016)
Masoumi, Mahdi, Zedan, Yasser, Texier, Damien, Jahazi, Mohammad et Bocher, Philippe.
2016.
« The influence of tool geometry on mechanical properties of friction stir welded AA-2024 and AA-2198 joints ».
In 34th International Conference and Exhibition of ICSOBA (Quebec, QC, Canada, Oct. 03-06, 2016)
The International Committee for Study of Bauxite, Alumina & Aluminium (ICSOBA).
Michel, Hesser Taboada, Reda, Layla Sasaki, Santos, Georgia Effgen, Cormier, Jonathan, Dumont, Christian, Villechaise, Patrick, Bocher, Philippe, Texier, Damien, Georges, Eric, Bridier, Florent, Hamon, Florence et Devaux, Alexandre.
2016.
« Mechanical properties of cast wrought hybrid disks ».
In Superalloys 2016: Proceedings of the 13th International Symposium on Superalloys (Seven Springs, PA, USA, Sept. 11-15, 2016)
pp. 539-548.
Minerals, Metals and Materials Society.
Novelli, Marc, Fundenberger, Jean-Jacques, Bocher, Philippe et Grosdidier, Thierry.
2016.
« On the effectiveness of surface severe plastic deformation by shot peening at cryogenic temperature ».
Applied Surface Science, vol. 389.
pp. 1169-1174.
Pourian, Meysam H., Bridier, Florent, Pilvin, Philippe et Bocher, Philippe.
2016.
« Prediction of crack initiation sites in alpha Ti-alloys microstructures under dwell-fatigue using Cellular Automaton simulation method ».
International Journal of Fatigue, vol. 85.
pp. 85-97. Quevedo Gonzalez, Fernando, Vanderesse, Nicolas, Barraud, Anthony, Bocher, Philippe et Nuño, Natalia. 2016. « Prediction and measurement of apparent elastic moduli in porous additive manufactured materials for new generation of hip implants ». Affiche présentée lors de la conférence : 10th World Biomaterials Congress (Montreal, QC, Canada, May 17-22, 2016).
Savaria, Vincent, Bridier, Florent et Bocher, Philippe.
2016.
« Predicting the effects of material properties gradient and residual stresses on the bending fatigue strength of induction hardened aeronautical gears ».
International Journal of Fatigue, vol. 85.
pp. 70-84.
Stinville, J. C., Echlin, M. P., Texier, D., Bridier, F., Bocher, P. et Pollock, T. M..
2016.
« Sub-grain scale digital image correlation by electron microscopy for polycrystalline materials during elastic and plastic deformation ».
Experimental Mechanics, vol. 56, nº 2.
pp. 197-216.
Texier, D., Zedan, Y., Amoros, T., Feulvarch, E., Stinville, J. C. et Bocher, P..
2016.
« Near-surface mechanical heterogeneities in a dissimilar aluminum alloys friction stir welded joint ».
Materials and Design, vol. 108.
pp. 217-229.
Vanderesse, N., Anderson, M., Bridier, F. et Bocher, P..
2016.
« Inter- and intragranular delta phase quantitative characterization in Inconel 718 by means of image analysis ».
Journal of Microscopy, vol. 261, nº 1.
pp. 79-87.
Vanderesse, N., Ky, I., Quevedo Gonzalez, F., Nuño, N. et Bocher, P..
2016.
« Image analysis characterization of periodic porous materials produced by additive manufacturing ».
Materials and Design, vol. 92.
pp. 767-778. 2015
Hamid Pourian, Meysam, Pilvin, Philippe, Bridier, Florent et Bocher, Philippe.
2015.
« Modeling the elastoplastic behaviors of alpha Ti-alloys microstructure using Cellular Automaton and finite element methods ».
Computational Materials Science, vol. 99.
pp. 33-42.
Kamkar, N., Bridier, F., Jedrzejowski, P. et Bocher, Philippe.
2015.
« Water droplet impact erosion damage initiation in forged Ti-6Al-4V ».
Wear, vol. 322-323.
pp. 192-202.
McMeekn, Kevin, Sirois, Frédéric, Bocher, Philippe et Tousignant, Maxime.
2015.
« Equivalent permeability model to simplify the nonlinear hysteretic B-H curve in time harmonic FEM simulations of induction heating ».
In 20th International Conference on the Computation of Electromagnetic Fields (Compumag 2015) (Montréal, QC, Canada, June 28-July 2, 2015)
pp. 333-334.
International Compumag Society.
Mokhtabad Amrei, Mohsen, Verreman, Yves, Bridier, Florent, Thibault, Denis et Bocher, Philippe.
2015.
« Microstructure characterization of single and multipass 13Cr4Ni steel welded joints ».
Metallography, Microstructure, and Analysis, vol. 4, nº 3.
pp. 207-218.
Paquin, Mathieu, Thibault, Denis, Bocher, Philippe, Lévesque, Jean-Benoît, Verreman, Yves et Shinozaki, Kenji.
2015.
« Assessment of cold cracking tests for low transformation temperature martensitic stainless steel multipass welds ».
Welding in the World, vol. 59, nº 4.
pp. 521-532.
Quevedo, F., Vanderesse, N., Bocher, P. et Nuño, N..
2015.
« Characterization and simulation of manufacturing irregularities of additive manufactured well-ordered porous materials ».
In Advanced Manufacturing Canada (AMC 2015) (Montreal, QC, Canada, Nov. 18-19, 2015)
Robe, Hugo, Zedan, Yasser, Chen, Jianqiang, Monajati, Hossein, Feulvarch, Eric et Bocher, Philippe.
2015.
« Microstructural and mechanical characterization of a dissimilar friction stir welded butt joint made of AA2024-T3 and AA2198-T3 ».
Materials Characterization, vol. 110.
pp. 242-251.
Savaria, V., Monajati, H., Bridier, F. et Bocher, Philippe.
2015.
« Measurement and correction of residual stress gradients in aeronautical gears after various induction surface hardening treatments ».
Journal of Materials Processing Technology, vol. 220.
pp. 113-123.
Stinville, J. C., Bridier, F., Ponsen, D., Wanjara, P. et Bocher, Philippe.
2015.
« High and low cycle fatigue behavior of linear friction welded Ti-6Al-4V ».
International Journal of Fatigue, vol. 70.
pp. 278-288.
Stinville, J. C., Vanderesse, N., Bridier, F., Bocher, P. et Pollock, T. M..
2015.
« High resolution mapping of strain localization near twin boundaries in a nickel-based superalloy ».
Acta Materialia, vol. 98.
pp. 29-42.
Strano, Matteo, Marra, Alessandro, Mussi, Valerio, Goletti, Massimo et Bocher, Philippe.
2015.
« Endurance of damping properties of foam-filled tubes ».
Materials, vol. 8, nº 7.
pp. 4061-4079.
Toubal, Lotfi, Bocher, Philippe et Moreau, André.
2015.
« Bimodal dwell-fatigue Weibull distribution of forged titanium IMI 834 ».
International Journal of Damage Mechanics, vol. 24, nº 5.
pp. 629-645. 2014
Bridier, Florent, Stinville, Jean-Charles, Vanderesse, Nicolas, Villechaise, Patrick et Bocher, Philippe.
2014.
« Microscopic strain and crystal rotation measurement within metallurgical grains ».
In Materials Structure and Micromechanics of Fracture VII (Brno, Czech Republic, July 1-3, 2013)
Coll. « Key Engineering Materials », vol. 592-593.
pp. 493-496.
Trans Tech Publications Ltd.
Ebrahimi, Gholam Reza, Momeni, Amir, Jahazi, Mohammad et Bocher, Philippe.
2014.
« Dynamic recrystallization and precipitation in 13Cr super-martensitic stainless steels ».
Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, vol. 45, nº 4.
pp. 2219-2231.
Gagnon, Martin, Tahan, Antoine, Bocher, Philippe et Thibault, Denis.
2014.
« Influence of load spectrum assumptions on the expected reliability of hydroelectric turbines: A case study ».
Structural Safety, vol. 50.
pp. 1-8.
Hoseini, Majid, Bocher, Philippe, Shahryari, Arash, Azari, Fereshteh, Szpunar, Jerzy A. et Vali, Hojatollah.
2014.
« On the importance of crystallographic texture in the biocompatibility of titanium based substrate ».
Journal of Biomedical Materials Research - Part A, vol. 102, nº 10.
pp. 3631-3638.
Jomaa, W., Songmene, Victor et Bocher, Philippe.
2014.
« Surface finish and residual stresses induced by orthogonal dry machining of AA7075-T651 ».
Materials, vol. 7, nº 3.
pp. 1603-1624.
Jomaa, Walid, Daoud, Monzer, Songmene, Victor, Bocher, Philippe et Châtelain, Jean-François.
2014.
« Identification and validation of Marusich's constitutive law for finite element modeling of high speed machining ».
In ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE) (Montreal, QC, Canada, Nov. 14-20, 2014)
American Society of Mechanical Engineers (ASME). Jomaa, Walid, Songmene, Victor et Bocher, Philippe. 2014. « Material behavior modeling during high speed machining of 6061-T6 and 7075-T651 alloys ». Affiche présentée lors de la conférence : Journée des étudiants du REGAL (JER2014) (Sherbrooke, QC, Canada, Nov. 18, 2014).
Lapalme, Maxime, Hoseini, Majid, Bocher, Philippe, Colle, Alain R. et Levesque, Martin.
2014.
« Realistic cold expansion finite element model and experimental validations for aluminium alloys ».
Experimental Mechanics, vol. 54, nº 5.
pp. 841-855.
Momeni, A., Ebrahimi, G. R., Jahazi, Mohammad et Bocher, Philippe.
2014.
« Microstructure evolution at the onset of discontinuous dynamic recrystallization: a physics-based model of subgrain critical size ».
Journal of Alloys and Compounds, vol. 587.
pp. 199-210.
Pourian, Meysam H., Pilvin, Philippe, Bridier, Florent et Bocher, Philippe.
2014.
« Heterogeneous elastic behavior of HCP titanium polycrystalline aggregates simulated by cellular automaton and finite element ».
Computational Materials Science, vol. 92.
pp. 468-475.
Ruiz-Vargas, J., Siredey-Schwaller, N., Noyrez, P., Mathieu, S., Bocher, Philippe et Gey, N..
2014.
« Potential and limitations of microanalysis SEM techniques to characterize borides in brazed Ni-based superalloys ».
Materials Characterization, vol. 94.
pp. 46-57.
Savaria, Vincent, Bridier, Florent et Bocher, Philippe.
2014.
« Measuring in-depth residual stress gradients: The challenge of induction hardened parts ».
In International Conference on Residual Stresses 9 (ICRS 9) (Garmisch-Partenkirchen, Germany, Oct. 7-9, 2012)
Coll. « Materials Science Forum », vol. 768-769.
pp. 158-165.
Zurich-Durnten, Switzerland : Trans Tech Publications Ltd.
Touazine, H., Jahazi, Mohammad et Bocher, Philippe.
2014.
« Influence of hard turning on microstructure evolution in the subsurface layers of Inconel 718 ».
In ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE) (Montreal, QC, Canada, Nov. 14-20, 2014)
American Society of Mechanical Engineers (ASME). 2013
Anderson, Melissa, Gholipour, Javad, Bridier, Florent, Bocher, Philippe, Jahazi, Mohammad, Savoie, Jean et Wanjara, Priti.
2013.
« Improving the formability of stainless steel 321 through multistep deformation for hydroforming applications ».
Transactions of the Canadian Society for Mechanical Engineering, vol. 37, nº 1.
pp. 39-52.
Ansaripour, Amir, Monajatizadeh, Hossein, Bocher, Philippe et Asefi, Davoud.
2013.
« Evaluation of recovery and recrystallization in cold rolled low carbon steel by magnetic hysteresis loop measurements ».
In Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013)
pp. 225-233.
Warrendale, PA, USA : Association for Iron and Steel Technology.
Barka, N., Bocher, Philippe et Brousseau, J..
2013.
« Sensitivity study of hardness profile of 4340 specimen heated by induction process using axisymmetric modeling ».
International Journal of Advanced Manufacturing Technology, vol. 69, nº 9-12.
pp. 2747-2756.
Barka, Noureddine, El Ouafi, Abderrazak, Bocher, Philippe et Brousseau, Jean.
2013.
« Effects of material properties fornon-equilibrium conditions in induction heating process ».
In Environmental and Materials Engineering (Seoul, Korea, Dec. 9-10, 2012)
Coll. « Advanced Materials Research », vol. 664.
pp. 496-503.
Clausthal-Zellerfeld, Germany : Trans Tech Publications Ltd.
Barka, Noureddine, El Ouafi, Abderrazak, Bocher, Philippe et Brousseau, Jean.
2013.
« Explorative study and prediction of overtemperingregion of disc heated by induction process using 2D axisymmetric model and experimental tests ».
In Materials and Manufacturing Research (Hong Kong, China, Dec. 19-20, 2012)
Coll. « Advanced Materials Research », vol. 658.
pp. 259-265.
Trans Tech Publications.
Barka, Noureddine, Khelalfa, Abdel Jelil, Ouafi, Abderrazak El, Bocher, Philippe et Brousseau, Jean.
2013.
« Effect of skin depth on hardness profile of gear heated by induction using 2D model ».
In Environmental and Materials Engineering (Seoul, Korea, Dec. 9-10, 2012)
Coll. « Advanced Materials Research », vol. 664.
pp. 884-890.
Clausthal-Zellerfeld, Germany : Trans Tech Publications Ltd.
Barka, Noureddine, Ouafi, Abderrazak El, Bocher, Philippe, Brousseau, Jean et Chebak, Ahmed.
2013.
« Explorative study and prediction of overtempering region of disc heated by induction process using 2D axisymmetric model and experimental tests ».
In Materials Engineering for Advanced Technologies (ICMEAT 2012) (Xiamen, China, Dec. 27-28, 2012)
Coll. « Advanced Materials Research », vol. 631-632.
pp. 417-423.
Scientific.net.
Boutana, N., Bocher, P. et Jahazi, M..
2013.
« Discrepancy between fatigue and dwell-fatigue behavior of near alpha titanium alloys simulated by cellular automata ».
International Journal of Fatigue, vol. 51.
pp. 49-56.
Gagnon, M., Tahan, Antoine, Bocher, Philippe et Thibault, D..
2013.
« On the fatigue reliability of hydroelectric Francis runners ».
In 5th International Conference on Fatigue Design, Fatigue Design 2013 (Senlis, France, Nov. 27-28, 2013)
Coll. « Procedia Engineering », vol. 66.
pp. 565-574.
Gagnon, Martin, Tahan, Antoine, Bocher, Philippe et Thibault, Denis.
2013.
« A probabilistic model for the onset of High Cycle Fatigue (HCF) crack propagation: Application to hydroelectric turbine runner ».
International Journal of Fatigue, vol. 47.
pp. 300-307.
Gariepy, A., Bridier, F., Hoseini, M., Bocher, Philippe, Perron, C. et Levesque, M..
2013.
« Experimental and numerical investigation of material heterogeneity in shot peened aluminium alloy AA2024-T351 ».
Surface and Coatings Technology, vol. 219.
pp. 15-30.
Gariepy, A., Larose, S., Perron, C., Bocher, Philippe et Levesque, M..
2013.
« On the effect of the orientation of sheet rolling direction in shot peen forming ».
Journal of Materials Processing Technology, vol. 213, nº 6.
pp. 926-938.
Gariepy, A., Larose, S., Perron, C., Bocher, Philippe et Levesque, M..
2013.
« On the effect of the peening trajectory in shot peen forming ».
Finite Elements in Analysis and Design, vol. 69.
pp. 48-61.
Jomaa, W., Songmene, Victor et Bocher, Philippe.
2013.
« On residual stress changes after orthogonal machining of induction hardened AISI 4340 steel ».
In Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013)
pp. 94-103.
Warrendale, PA, USA : Association for Iron and Steel Technology.
Kamkar, N., Bridier, Florent, Bocher, Philippe et Jedrzejowski, P..
2013.
« Water droplet erosion mechanisms in rolled Ti-6Al-4V ».
Wear, vol. 301, nº 1-2.
pp. 442-448.
Kassab, Rabih, Champliaud, Henri, Bocher, Philippe, Lanteigne, Jacques et Lê, Van Ngan.
2013.
« Strain variations of AISI 4340 steel undergoing metallurgical transformations during induction hardening heat treatment ».
In Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013)
pp. 774-783.
Warrendale, PA, USA : Association for Iron and Steel Technology.
Larregain, Benjamin, Vanderesse, Nicolas, Bridier, Florent, Bocher, Philippe et Arkinson, Patrick.
2013.
« Method for accurate surface temperature measurements during fast induction heating ».
[Article de conférence]. Journal of Materials Engineering and Performance, vol. 22, nº 7.
pp. 1907-1913.
Maldar, A. R., Ebrahimi, G. R., Haghshenas, Meysam, Jahazi, M. et Bocher, P..
2013.
« Thermomechanical characterization of Mg-9Al-1Zn alloy using power dissipation maps ».
Journal of Materials Engineering and Performance, vol. 22, nº 11.
pp. 3306-3314.
Moreau, A., Toubal, L., Bocher, Philippe, Humbert, M., Uta, E. et Gey, N..
2013.
« Evaluation of macrozone dimensions by ultrasound and EBSD techniques ».
Materials Characterization, vol. 75.
pp. 115-128.
Paquin, M., Thibault, D., Bocher, Philippe et Verreman, Y..
2013.
« Study on cold cracking test methods for low carbon soft-martensitic stainless steel flux cored arc welding ».
In Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013)
pp. 733-744.
Warrendale, PA, USA : Association for Iron and Steel Technology.
Ruiz-Vargas, J., Siredey-Schwaller, N., Bocher, Philippe et Hazotte, A..
2013.
« First melting stages during isothermal brazing, of Ni/BNi-2 couples ».
Journal of Materials Processing Technology, vol. 213, nº 12.
pp. 2074-2080.
Shahriari, D., Zolfaghari, A., Jahazi, Mohammad et Bocher, Philippe.
2013.
« Development of an expert system to characterize weld defects identified by ultrasonic testing ».
In American Society of Mechanical Engineers, Pressure Vessels and Piping Division (Publication) PVP (Paris, France, July 14-18, 2013)
New York, NY, USA : American Society of Mechanical Engineers.
Yi, J., Gharghouri, M., Bocher, Philippe et Medraj, M..
2013.
« Distortion and residual stress measurements of induction hardened AISI 4340 discs ».
Materials Chemistry and Physics, vol. 142, nº 1.
pp. 248-258. 2012
Anderson, Melissa, Bocher, Philippe, Gholipour, Javad, Jahazi, Mohammad, Savoie, Jean et Wanjara, Priti.
2012.
« Increasing the hydroformability of stainless steel 321 by multistep processing ».
In Proceedings of the 14th International Conference on Metal Forming, METAL FORMING 2012 (Krakow, Poland, Sept. 16-19, 2012)
Coll. « Steel Research International »
pp. 1243-1246.
Krakow, Poland : Wiley-VCH Verlag.
Barka, Noureddine, Chebak, Ahmed, Ouafi, Abderrazakel, Bocher, Philippe et Brousseau, Jean.
2012.
« Sensitivity study of temperature profile of 4340 spur gear heated by induction process using 3D model ».
In Mechanical and Aerospace Engineering (Paris, France, July 7-8, 2012)
Coll. « Applied Mechanics and Materials », vol. 232.
pp. 736-741.
Trans Tech Publications.
Barka, Noureddine, El Ouafi, Abderrazak, Chebak, Ahmed, Bocher, Philippe et Brousseau, Jean.
2012.
« Study of induction heating process applied to internal gear using 3D model ».
In Mechanical and Aerospace Engineering (Paris, France, July 7-8, 2012)
Coll. « Applied Mechanics and Materials », vol. 232.
pp. 730-735.
Trans Tech Publications.
Gagnon, M., Tahan, Antoine, Bocher, Philippe et Thibault, D..
2012.
« The role of high cycle fatigue (HCF) onset in Francis runner reliability ».
In 26th IAHR Symposium on Hydraulic Machinery and Systems (Beijing, China, Aug. 19-23, 2012)
Coll. « IOP Conference Series: Earth and Environmental Science », vol. 15.
UK : IOP Publishing Ltd..
Gagnon, Martin, Tahan, Antoine, Bocher, Philippe et Thibault, Denis.
2012.
« On the stochastic simulation of hydroelectric turbine blades transient response ».
Mechanical Systems and Signal Processing, vol. 32.
pp. 178-187.
Gariepy, A., Cyr, J., Levers, A., Perron, C., Bocher, P. et Lévesque, M..
2012.
« Potential applications of peen forming finite element modelling ».
Advances in Engineering Software, vol. 52.
pp. 60-71.
Gey, N., Bocher, P., Uta, E., Germain, L. et Humbert, M..
2012.
« Texture and microtexture variations in a near-α titanium forged disk of bimodal microstructure ».
Acta Materialia, vol. 60, nº 6-7.
pp. 2647-2655.
Gey, N., Bocher, Philippe, Uta, E., Humbert, M. et Gilgert, J..
2012.
« How texture and microtexture influence dwell fatigue lifetime in forged IMI834 titanium alloys ».
In Ti 2011 - Proceedings of the 12th World Conference on Titanium (Beijing, China, June 19-24, 2011)
pp. 879-882.
Beijing, China : Science Press.
Hoseini, Majid, Bocher, Philippe, Azari, Fereshteh, Vali, Hojatollah et Szpunar, Jerzy A..
2012.
« Effects of grain size and texture on the biocompatibility of commercially pure titanium ».
In 16th International Conference on Textures of Materials (Mumbai, India, Dec. 12-17, 2011 )
Coll. « Materials Science Forum », vol. 702-703.
pp. 822-825.
Trans Tech Publications Ltd.
Hoseini, Majid, Bridier, Florent, Bocher, Philippe, Vali, Hojatollah et Szpunar, Jerzy A..
2012.
« Thermal stability and grain growth behavior of ultrafine grained commercially pure titanium fabricated by equal channel angular pressing ».
In Ti 2011 - Proceedings of the 12th World Conference on Titanium (Beijing, China, June 19-24, 2011)
pp. 666-670.
Beijing, China : Science Press.
Hoseini, Majid, Hamid Pourian, Meysam, Bridier, Florent, Vali, Hojatollah, Szpunar, Jerzy A. et Bocher, Philippe.
2012.
« Thermal stability and annealing behaviour of ultrafine grained commercially pure titanium ».
Materials Science and Engineering: A, vol. 532.
pp. 58-63.
Ruiz-Vargas, J., Siredey-Schwaller, N., Gey, N., Bocher, P. et Hazotte, A..
2012.
« Microstructure development during isothermal brazing of Ni/BNi-2 couples ».
Journal of Materials Processing Technology, vol. 213, nº 1.
pp. 20-29.
Savaria, Vincent, Bridier, Florent et Bocher, Philippe.
2012.
« Computational quantification and correction of the errors induced by layer removal for subsurface residual stress measurements ».
International Journal of Mechanical Sciences, vol. 64, nº 1.
pp. 184-195. 2011
Barka, N., Bocher, Philippe, Brousseau, J. et Arkinson, P..
2011.
« Effect of dimensional variation on induction process parameters using 2D simulation ».
In THERMEC 2011 Supplement (Quebec City, QC, Canada, Aug. 1-5, 2011)
Coll. « Advanced Materials Research », vol. 409.
pp. 395-400.
Germany : Trans Tech Publications.
Candeo, Alessandro, Ducassy, Christophe, Bocher, Philippe et Dughiero, Fabrizio.
2011.
« Multiphysics modeling of induction hardening of ring gears for the aerospace industry ».
IEEE Transactions on Magnetics, vol. 47, nº 5.
pp. 918-921.
Savaria, Vincent, Hoseini, Majid, Bridier, Florent, Bocher, Philippe et Arkinson, Patrick.
2011.
« On the measurement of residual stress in induction hardened parts ».
In Residual Stresses VIII (Riva del Garda, Trento, Italy, June 26-28, 2010)
Coll. « Materials Science Forum », vol. 681.
pp. 431-436.
Thibault, Denis, Bocher, Philippe, Thomas, Marc, Lanteigne, Jacques, Hovington, Pierre et Robichaud, Patrice.
2011.
« Reformed austenite transformation during fatigue crack propagation of 13%Cr-4%Ni stainless steel ».
Materials Science and Engineering: A, vol. 528, nº 21.
pp. 6519-6526. 2010
Anderson, M., Gholipour, J., Bocher, Philippe, Bridier, F., Savoie, J. et Wanjara, P..
2010.
« Formability extension of aerospace alloys for tube hydroforming applications ».
International Journal of Material Forming, vol. 3, nº Suppl. 1.
pp. 303-306.
Bastajib, N., Boutana, N., Bocher, P. et Jahazi, M..
2010.
« Application of cellular automata method to simulate the hot deformation behavior of a dual phase titanium alloy ».
Technische Mechanik, vol. 30, nº 1-3.
Candeo, Alessandro, Bocher, Philippe et Dughiero, Fabrizio.
2010.
« Multiphysics modeling of induction hardening of ring gears for the aerospace industry ».
In 14th Biennial IEEE Conference on Electromagnetic Field Computation (CEFC 2010) (Chicago, IL, USA, May 09-12, 2010)
IEEE.
Gagnon, Martin, Tahan, Antoine, Bocher, Philippe et Thibault, Denis.
2010.
« Impact of startup scheme on Francis runner life expectancy ».
In 25th IAHR Symposium on Hydraulic Machinery and Systems (Timişoara, Romania, 20–24 Sept. 2010)
Coll. « IOP Conference Series : Earth and Environmental Science », vol. 12.
012107.
London, UK : Institute of Physics Publishing.
Thibault, Denis, Bocher, Philippe, Thomas, Marc, Gharghouri, Michael et Coté, Marjolaine.
2010.
« Residual stress characterization in low transformation temperature 13%Cr-4%Ni stainless steel weld by neutron diffraction and the contour method ».
Materials Science and Engineering: A, vol. 527, nº 23.
pp. 6205-6210.
Toubal, Lotfi, Bocher, Philippe, Moreau, André et Levesque, Daniel.
2010.
« Macroregion size measurements in bimodal titanium forgings using two-dimensional autocorrelation method ».
Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, vol. 41A, nº 3.
pp. 744-750. 2009
Bocher, Philippe, Bridier, F., Toubal, L., Boutana, N., Uta, E., Gey, N. et Humbert, M..
2009.
« Dwell-fatigue in near alpha titanium alloys: A multiscale, interdisciplinary challenge ».
In 12th International Conference on Fracture 2009, ICF-12 (Ottawa, ON, Canada, July 12-17, 2009)
pp. 1481-1486.
International Congress on Fracture.
Hacini, L., Lê, Van Ngan et Bocher, Philippe.
2009.
« Evaluation of residual stresses induced by robotized hammer peening by the contour method ».
Experimental Mechanics, vol. 49, nº 6.
pp. 775-783.
Humbert, M., Moreau, A., Uta, E., Gey, N., Bocher, Philippe et Bescond, C..
2009.
« Analysis of backscattered ultrasound amplitude of Ti-5.8Al-4Sn-3.5Zr-0.7Nb-0.5Mo-0.3Si samples in terms of their microstructures and local textures ».
Acta Materialia, vol. 57, nº 3.
pp. 708-714.
Thibault, Denis, Bocher, Philippe et Thomas, Marc.
2009.
« Residual stress and microstructure in welds of 13%Cr-4%Ni martensitic stainless steel ».
Journal of Materials Processing Technology, vol. 209, nº 4.
pp. 2195-2202.
Toubal, L., Bocher, Philippe et Moreau, A..
2009.
« Dwell-fatigue life of a near-alpha titanium alloy and ultrasonic measurement correlation ».
In 12th International Conference on Fracture 2009, ICF-12 (Ottawa, ON, Canada, July 12-17, 2009)
pp. 1123-1128.
International Congress on Fracture.
Toubal, Lotfi, Bocher, Philippe et Moreau, André.
2009.
« Dwell-fatigue life dispersion of a near alpha titanium alloy ».
International Journal of Fatigue, vol. 31, nº 3.
pp. 601-605.
Uta, E., Gey, N., Bocher, Philippe, Humbert, M. et Gilgert, J..
2009.
« Texture heterogeneities in alpha(p)/alpha(s) titanium forging analysed by EBSD-Relation to fatigue crack propagation ».
Journal of Microscopy, vol. 233, nº 3.
pp. 451-459. 2008
Boutana, N., Bocher, P., Jahazi, M., Piot, D. et Montheillet, F..
2008.
« Microstructural modeling of cold creep/fatigue in near alpha titanium alloys using cellular automata method ».
Transactions of the Canadian Society for Mechanical Engineering, vol. 32, nº 2.
pp. 195-213.
Boutana, N., Bocher, Philippe, Jahazi, M., Piot, D. et Montheillet, F..
2008.
« The microstructural modeling of room temperature creep in titanium alloys using cellular automata model ».
International Journal of Microstructure and Materials Properties, vol. 3, nº 4-5.
pp. 642-653.
Germain, L., Gey, N., Humbert, M., Vo, P., Jahazi, M. et Bocher, Philippe.
2008.
« Texture heterogeneities induced by subtransus processing of near alpha titanium alloys ».
Acta Materialia, vol. 56, nº 16.
pp. 4298-4308.
Hacini, Lyes, Lê, Van Ngan et Bocher, Philippe.
2008.
« Effect of impact energy on residual stresses induced by hammer peening of 304L plates ».
Journal of Materials Processing Technology, vol. 208, nº 1-3.
pp. 542-548. Monajati, H., Jahazi, M., Bocher, Philippe et Yue, S.. 2008. « Dynamic recrystallization investigation during hot deformation of Udimet 720 nickel base superalloy ». Communication lors de la conférence : 14th International Metallurgy and Materials Congress (Istanbul, Turkey, Oct. 16-18, 2008). Moreau, A., Kruger, S.E., Côté, M. et Bocher, Philippe. 2008. « In-Situ monitoring of microstructure during thermomechanical simulations using laser-ultrasonics ». Communication lors de la conférence : 1st Interntional Symposium on Laser Ultrasonics : Science, Technology and Applications (Montreal, QC, Canada, July 16-18, 2008).
Moreau, André, Kruger, Silvio E., Côté, Marjolaine et Bocher, Philippe.
2008.
« In-Situ monitoring of microstructure during thermomechanical simulations using laser-ultrasonics ».
In 1st Interntional Symposium on Laser Ultrasonics : Science, Technology and Applications (Montreal, QC, Canada, July 16-18, 2008)
Uta, E., Bocher, Philippe, Gey, N., Humbert, M. et Gilbert, J.. 2008. « EBSD analysis of Dwell-fatigue fracture surface in titanium alloy IMI 834 ». Communication lors de la conférence : JIP, Fatigue and Plasticity : from Mechanisms to Design (Paris, France, May 20-22, 2008).
Uta, E., Bocher, Philippe, Gey, N., Humbert, M. et Gilgert, J..
2008.
« EBSD analyses of dwell fracture surface in titanium alloy IMI-834 ».
In International Conference Fatigue and Plasticity From Mechanisms to Design (JIP) (Paris, France, May 20-22, 2008)
pp. 315-322.
2007
Arafin, M. A., Medraj, M., Turner, D. P. et Bocher, Philippe.
2007.
« Effect of alloying elements on the isothermal solidification during TLP bonding of SS 410 and SS 321 using a BNi-2 interlayer ».
Materials Chemistry and Physics, vol. 106, nº 1.
pp. 109-119.
Arafin, M. A., Medraj, M., Turner, Daniel P. et Bocher, Philippe.
2007.
« Transient liquid phase bonding of Inconel 718 and Inconel 625 with BNi-2: modeling and experimental investigations ».
Materials Science and Engineering: A, vol. 447, nº 1-2.
pp. 125-133. Barka, N., Khelalfa, A., Bocher, Philippe, Brousseau, J. et Sundararajan, S.. 2007. « Analysis of the effect of frequency using numerical modeling of induction hardening process ». Communication lors de la conférence : 1st International Conference of Sustainable Manufacturing (Montreal, QC, Canada, Oct. 18-19, 2007). Boutana, N., Bocher, Philippe, Jahazi, M., Piot, D. et Montheillet, F.. 2007. « Microstructural modeling of cold creep/fatigue in near alpha titanium alloys using cellular automata method ». Communication lors de la conférence : 11th World Conference on Titanium (Kyoto, Japan, June 3-7, 2007). Boutana, N., Bocher, Philippe, Jahazi, M., Piot, D. et Montheillet, F.. 2007. « Simulation of the mechanical behavior of hetegeogeneous materials using cellular automata ». Communication lors de la conférence : 1st International Conference of Sustainable Manufacturing (Montreal, QC, Canada, Oct. 18-19, 2007).
Boutana, N., Bocher, Philippe, Jahazi, M., Piot, D. et Motheillet, F..
2007.
« Microstructural modeling of cold creep/fatigue in near alpha titanium alloys using cellular automata method ».
In Proceedings of TI-2007, 11th World Conference on Titanium (Kyoto, Japan, June 3-7, 2007)
pp. 267-270.
Warrendale, PA, USA : Minerals, Metals and Materials Society. Germain, L., Vo, P., Gey, N., Jahazi, M., Humbert, M. et Bocher, Philippe. 2007. « Develpment of sharp local alpha microtectures during alpha/beta thermo-mechanical processing of Timetal 834 ». Communication lors de la conférence : 11th World Conference on Titanium (Kyoto, Japan, June 3-7, 2007).
Germain, Lionel, Vo, Phuong, Gey, Nathalie, Jahazi, Mohammad, Humbert, Michel et Bocher, Philippe.
2007.
« Development of sharp local α microtextures during α/β thermo-mechanical processing of TIMETAL 834 ».
In 11th World Conference on Titanium (Kyoto, Japan, June 3-7, 2007)
pp. 925-928.
Warrendale, USA : Minerals, Metals and Materials Society.
Hacini, L., Lê, Van Ngan et Bocher, Philippe.
2007.
« Traitement de surfaces par impacts : évaluation des contraintes résiduelles induites par martelage ».
In 18e Congrès Français de Mécanique (Grenoble, France, 27-31 août 2007)
Courbevoie, France : AFM, Maison de la Mécanique. Thibault-Liboiron, K., Alderliesten, R., Benedictus, R. et Bocher, Philippe. 2007. « Off-axis crack propagation and delamination growth in FML's ». Communication lors de la conférence : 6th Canadian International Conference on Composites (CANCOM) (Winnipeg, MB, Canada, Aug. 14-17, 2007). Uta, E., Humbert, M., Gey, N., Hazotte, A., Bocher, Philippe et Jahazi, M.. 2007. « Description and characterisation of texture heterogeneities in titanium alloy Timetal 834 with a bimodal microstructure ». Communication lors de la conférence : World Titanium Conference (Kyoto, Japan, June 3-7, 2007).
Uta, E., Humbert, M., Gey, N., Hazotte, A., Bocher, Philippe et Jahazi, M..
2007.
« Description and characterisation of texture heterogeneitites in titanium alloy Timetal 834 with a bimodal microstructure ».
In 11th World Conference on Titanium (Kyoto, Japan, June 3-7, 2007)
pp. 259-262.
Warrendale, USA : Minerals, Metals and Materials Society.
Vo, Phuong, Jahazi, M., Yue, S. et Bocher, Philippe.
2007.
« Flow stress prediction during hot working of near-alpha titanium alloys ».
Materials Science and Engineering: A, vol. 447, nº 1-2.
pp. 99-110. 2006
Arafin, M. A., Medraj, M., Turner, D. P. et Bocher, P..
2006.
« Optimization of process variables during TLP Bonding of nickel superalloys ».
In Aerospace materials and manufacturing : emerging materials, processes, and repair techniques : proceedings of the third International [Symposium] on Aerospace Materials and Manufacturing : emerging materials, processes and repair techniques, October 1-4, (Montreal, QC, Canada, Oct. 1-4, 2006)
pp. 301-314.
Canadian Institute of Mining, Metallurgy and Petroleum.
Arafin, M. A., Medraj, M., Turner, D. P. et Bocher, Philippe.
2006.
« Thermodynamic modeling and experimental investigation of brazed joints used in aerospace industry ».
In 3rd International Brazing and Soldering Conference (San Antonio, TX, USA, April 24-26, 2006)
pp. 189-196.
Materials Park, OH, USA : ASM International.
Arafin, Muhammad A., Medraj, Mamoun, Turner, Daniel P. et Bocher, Philippe.
2006.
« Mathematical Modeling and Experimental Investigations of Isothermal Solidification during Transient Liquid Phase Bonding of Nickel Superalloys ».
In THERMEC 2006 Supplement (Vancouver, Canada, Jul. 4 - 8, 2006)
Coll. « Advanced Materials Research », vol. 15-17.
pp. 882-887.
Clausthal-Zellerfeld, Germany : Trans Tech Publications.
Barka, N., Bocher, Philippe, Brousseau, J., Galopin, Michel et Sundararajan, S..
2006.
« Modeling and sensitivity study of the induction hardening process ».
In THERMEC 2006 Supplement (Vancouver, Canada, Jul. 4-8, 2006)
Coll. « Advanced Materials Research », vol. 15-17.
pp. 525-530.
Uetikon-Zuerich, Switzerland : Trans Tech Publications.
Barka, N., Bocher, Philippe, Galopin, Michel, Brousseau, J. et Sundararajan, S..
2006.
« Sensitivity study of induction hardening machine parameters of SAE-4340 steel specimen ».
In Conference of Metallurgists (COM) (Montreal, QC, Canada, Oct. 1-4, 2006)
pp. 525-530.
Montreal, Canada : The Metallurgy and Materials Society of CIM.
Boutana, Nabil, Bocher, Philippe, Jahazi, Mohammad, Piot, D. et Montheillet, F..
2006.
« Utilisation des automates cellulaires pour étudier le comportement en fatigue-fluage des alliages de titane ».
In Matériaux 2006 (Dijon, France, 13-17 nov. 2006)
pp. 781-790.
Dubourg, L., Jahazi, M., Dezaise, G. et Bocher, P..
2006.
« Microstructure and mechanical characterisation of FSW 7075-T6 lap joints ».
In Aerospace Materials and Manufacturing: Emerging Materials, Processes, and Repair Techniques (Montréal, Canada, Oct.1-4, 2006)
pp. 107-120.
Canadian Institute of Mining, Metallurgy and Petroleum.
Hacini, L., Lê, Van Ngan, Bocher, Philippe et Thibault, D..
2006.
« Effect of energy level on stresses induced by robotized hammer peening ».
In Conference of Metallurgists (COM) (Montreal, QC, Canada, Oct.1-4, 2006)
781-790 .
Montreal, Canada : The Metallurgy and Materials Society of CIM.
Hacini, L., Lê, Van Ngan, Bocher, Philippe et Thibault, D..
2006.
« Residual stresses induced by robotized hammer peening : the effect of impact energy level ».
In Aerospace materials and manufacturing : emerging materials, processes, and repair techniques : proceedings of the third International [Symposium] on Aerospace Materials and Manufacturing : emerging materials, processes and repair techniques, October 1-4, (Montreal, QC, Canada, Oct. 2-4, 2006)
pp. 759-768.
Montreal : Canadian Institute of Mining, Metallurgy and Petroleum.
Humbert, Michel, Germain, L., Gey, N., Bocher, Philippe et Jahazi, M..
2006.
« Study of the variant selection in sharp textured regions of bimodal IMI 834 billet ».
Materials Science and Engineering: A, vol. 430, nº 1-2.
pp. 157-164.
Uta, E., Humbert, M., Gey, N., Bocher, P. et Jahazi, M..
2006.
« Mise en évidence et caractérisation des hétérogénéités de textures dans l'alliage de titane IMI 834 de microstructure bimodale à vocation aéronautique ».
In Materiaux 2006 : Dijon, 13-17 Novembre 2006 : [recueil de la conference sur CD-ROM] (Dijon, France, 13-17 nov. 2006)
Dijon : Université de Bourgogne. 2005
Bocher, P., Jahazi, M., Germain, L., Gey, N. et Humbert, M..
2005.
« Variant selection in forged titanium alloys : effect of microscopic grain misorientations on the formation of macroscopic regions with similar crystallographic orientations ».
In Materials for safety and health : mesoscopic and multiscale consideration in modern science and engineering (Montreal, QC, Canada, Aug. 1-4, 2005)
pp. 523-530.
Montréal, Qué., Canada : École de technologie supérieure.
Bocher, Philippe, Jahazi, Mohammad, Germain, Lionel, Wanjara, Priti, Gey, Nathalie et Humbert, Michel.
2005.
« β Microtexture analysis in correlation with hcp textured regions observed in a forged near alpha titanium alloy ».
Solid State Phenomena, vol. 105.
pp. 127-132.
Boutana, N., Bocher, P., Jahazi, M., Savoie, J., Piot, D. et Montheillet, F..
2005.
« Modelling mechanical behaviour of heterogeneous materials using cellular automata : application to some forged titanium alloys ».
In Materials for safety and health : mesoscopic and multiscale consideration in modern science and engineering (Montreal, QC, Canada, Aug. 1-4, 2005)
pp. 273-280.
Montréal, Qué., Canada : École de technologie supérieure.
Germain, L., Gey, N., Humbert, M., Bocher, P. et Jahazi, M..
2005.
« β→-αs variant selection in sharp hcp textured regions of a bimodal IMI834 billet ».
In Proceedings of the 14th International Conference on Textures of Materials (Leuven, Belgium, July 11-15, 2005)
Coll. « Materials Science Forum », vol. 495-497.
pp. 663-668.
Trans Tech Publications.
Germain, L., Gey, N., Humbert, M., Hazotte, A., Bocher, P. et Jahazi, M..
2005.
« An automated method to analyze separately the microtextures of primary αp grains and the secondary αs inherited colonies in bimodal titanium alloys ».
Materials Characterization, vol. 54, nº 3.
pp. 216-222.
Germain, Lionel, Gey, Nathalie, Humbert, Ludovic, Bocher, Philippe et Jahazi, Mohammad.
2005.
« Analysis of sharp microtexture heterogeneities in a bimodal IMI 834 billet ».
Acta Materialia, vol. 53, nº 13.
pp. 3535-3543.
Khodabandeh, Ali Reza, Jahazi, Mohammad, Yue, Steve et Bocher, Philippe.
2005.
« Impact toughness and tensile properties improvement through microstructure control in hot forged Nb-V microalloyed steel ».
ISIJ International, vol. 45, nº 2.
pp. 272-280.
Wanjara, P., Monajati, H., Jahazi, M., Germain, L., Bocher, P. et Immarigeon, J.-P..
2005.
« Deformation processing mechanism and microstructural evolution in a near-alpha titanium alloy ».
In Materials science & technology: proceedings of the conference held September 25-28, 2005, Pittsburgh, Pennsylvania USA (Pittsburgh, PA, USA, Sept. 25-28, 2005)
pp. 15-26.
Association for Iron and Steel Technology. 2004Bocher, Philippe, Jahazi, M., Wanjara, P., Germain, L., Gey, N. et Humbert, M.. 2004. « Microtexture analysis in correlation with hcp textured regions observed in a forged near alpha titanium alloy ». Communication lors de la conférence : 2nd International Conference on Texture and Anisotropy of Polycrystals (ITAP-2) (Metz, France, July 7-9, 2004).
Jahazi, Mohammad, Germain, Lionel, Gey, Nathalie, Humbert, Michel et Bocher, Philippe.
2004.
« Specific EBSD data processing to analyse separately the ap/as microtexture of bimodal Titanium alloys ».
Materials Characterization, vol. 54.
pp. 216-222. 2003
Germain, L., Gey, N., Humbert, M., Bocher, P. et Jahazi, M..
2003.
« Texture and microtexture analysis of an IMI 834 alloy after thermo-mechanical processing ».
In Ti-2003 Science and Technology : proceedings of the 10th World Conference on Titanium held at the CCH-Congress Center Hamburg, Germany, 13-18 July 2003 (Hamburg, Germany, July 13-18, 2003)
pp. 1283-1290.
Weinheim, Allemagne : Wiley-VCH. |
![[Monter]](/style/images/multi_up.png)
Monter d'un niveau